图片
设为首页加入收藏
导航菜单
全站搜索
当前位置
产品详情
Cisco console cable
Cisco Console cable
If you want to buy online
https://www.aliexpress.com/store/product/One-piece-packing-by-China-post-only-USB-RS232-to-RJ45-console-cable/401907_2044331645.html?spm=2114.12010612.0.0.MUZS45


  • Cisco console cable
  • Cisco router console cable
  • cab-console-usb
  • USB2.0 compatible, full speed
  • USB UART RS232 cisco console cable
  • Support USB to cisco router controlling
  • Support Huawei, H3C, etc
  • FTDI chip, FT232RL+ZT213
  • Integrated EEPROM, support programmable
  • Support Win 8, Android, etc
  • Support 300 ~ 1Mbps baud rate
  • TX,RX,CTS,RTS,DTR,DSR,RI,DCD,RI, GND
  • Length: 3.6mtr, 1.8mtr, 0.3mtr optional
  • CE,ROHS

Cisco Auxiliary port for Cisco 1000, 1600, 2500, 2600, and 3600 series routers pinout

1-RTS,2-DTR, 3-TXD 4-Gnd, 5-Gnd, 5-RXD,7-DSR,8-CTS as DTE
So sinforcon cable is 1-CTS,2-DSR,3-RXD,4-GND, 5-GND,6-TXD, 7-DTR,8-RTS

思科路由器控制线, 华为路由器控制线,H3C控制线

支持华为,思科路由器,替代以前两条线一同用来控制路器的线

About FT232RL

The FT232R is the latest device to be added to FTDI?s range of USB UART interface Integrated Circuit Devices. The FT232R is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-ID? security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are available. USB to serial designs using the FT232R have been further simplified by fully integrating the external EEPROM, clock circuit and USB resistors onto the device.

The FT232R adds two new functions compared with its predecessors, effectively making it a "3-in-1" chip for some application areas. The internally generated clock (6MHz, 12MHz, 24MHz, and 48MHz) can be brought out of the device and used to drive a microcontroller or external logic. A unique number (the FTDIChip-ID?) is burnt into the device during manufacture and is readable over USB, thus forming the basis of a security dongle which can be used to protect customer application software from being copied.

  • Single chip USB to asynchronous serial data transfer interface.
  • Entire USB protocol handled on the chip - No USB-specific firmware programming required.
  • UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity.
  • Fully assisted hardware or X-On / X-Off software handshaking.
  • Data transfer rates from 300 baud to 3 Megabaud (RS422 / RS485 and at TTL levels) and 300 baud to 1 Megabaud (RS232).
  • In-built support for event characters and line break condition.
  • New USB FTDIChip-ID? feature.
  • New configurable CBUS I/O pins.
  • Auto transmit buffer control for RS485 applications.
  • Transmit and receive LED drive signals.
  • New 48MHz, 24MHz,12MHz, and 6MHz clock output signal Options for driving external MCU or FPGA.
  • FIFO receive and transmit buffers for high data throughput.
  • 256 Byte receive buffer and 128 Byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
  • Adjustable receive buffer timeout.
  • Synchronous and asynchronous bit bang mode interface options with RD# and WR# strobes.
  • New CBUS bit bang mode option.
  • Integrated 1024 bit internal EEPROM for I/O configuration and storing USB VID, PID, serial number and product description strings.
  • Device supplied preprogrammed with unique USB serial number.
  • Support for USB suspend / resume.
  • Support for bus powered, self powered, and high-power bus powered USB configurations.
  • Integrated 3.3V level converter for USB I/O .
  • Integrated level converter on UART and CBUS for interfacing to 5V - 1.8V Logic.
  • True 5V / 3.3V / 2.8V / 1.8V CMOS drive output and TTL input.
  • High I/O pin output drive option.
  • Integrated USB resistors.
  • Integrated power-on-reset circuit.
  • Fully integrated clock - no external crystal, oscillator, or resonator required.
  • Fully integrated AVCC supply filtering - No separate AVCC pin and no external R-C filter required.
  • UART signal inversion option.
  • USB bulk transfer mode.
  • 3.3V to 5.25V Single Supply Operation.
  • Low operating and USB suspend current.
  • Low USB bandwidth consumption.
  • UHCI / OHCI / EHCI host controller compatible.
  • USB 2.0 Full Speed compatible.
  • -40°C to 85°C extended operating temperature range.

RJ45 side pinout as following:

Serial Port
In computing, a serial port is a serial communication physical interface through which information transfers in or out one bit at a time (in contrast to a parallel port).Throughout most of the history of personal computers, data was transferred through serial ports to devices such as modems, terminals and various peripherals.Pair of female Mini DIN-8 connectors used for RS-422 serial ports on a Macintosh LC computerWhile such interfaces as Ethernet, FireWire, and USB all send data as a serial stream, the term "serial port" usually identifies hardware more or less compliant to the RS-232 standard, intended to interface with a modem or with a similar communication device.Modern computers without serial ports may require serial-to-USB converters to allow compatibility with RS 232 serial devices. Serial ports are still used in applications such as industrial automation systems, scientific instruments, shop till systems and some industrial and consumer products. Server computers may use a serial port as a control console for diagnostics. Network equipment (such as routers and switches) often use serial console for configuration. Serial ports are still used in these areas as they are simple, cheap and their console functions are highly standardized and widespread. A serial port requires very little supporting software

from the host system.
Some computers, used an integrated circuit called a UART, that converted characters to (and from) asynchronous serial form, and automatically looked after the timing and framing of data. Very low-cost systems, such as some early home computers, would instead use the CPU to send the data through an output pin, using the bit-banging technique. Before large-scale integration (LSI) UART integrated circuits were common, a minicomputer or microcomputer would have a serial port made of multiple small-scale integrated circuits to implement shift registers, logic gates, counters, and all the other logic for a serial port.Early home computers often had proprietary serial ports with pinouts and voltage levels incompatible with RS-232. Inter-operation with RS-232 devices may be impossible as the serial port cannot withstand the voltage levels produced and may have other differences that "lock in" the user to products of a particular manufacturer. Low-cost processors now allow higher-speed, but more complex, serial communication standards such as USB and FireWire to replace RS-232. These make it possible to connect devices that would not have operated feasibly over slower serial connections, such as mass storage, sound, and video devices.Many personal computer motherboards still have at least one serial port, even if accessible only through a pin header. Small-form-factor systems and laptops may omit RS-232 connector ports to conserve space, but the electronics are still there. RS-232 has been standard for so long that the circuits needed to control a serial port became very cheap and often exist on a single chip, sometimes also with circuitry for a parallel port.

DTE and DCE
The individual signals on a serial port are unidirectional and when connecting two devices the outputs of one device must be connected to the inputs of the other. Devices are divided into two categories "data terminal equipment" (DTE) and "data circuit-terminating equipment" (DCE). A line that is an output on a DTE device is an input on a DCE device and vice-versa so a DCE device can be connected to a DTE device with a straight wired cable. Conventionally, computers and terminals are DTE while modems and peripherals are DCE.If it is necessary to connect two DTE devices (or two DCE devices but that is more unusual) a cross-over null modem, in the form of either an adapter or a cable, must be used

Connectors
While the RS-232 standard originally specified a 25-pin D-type connector, many designers of personal computers chose to implement only a subset of the full standard: they traded off compatibility with the standard against the use of less costly and more compact connectors (in particular the DE-9 version used by the original IBM PC-AT). The desire to supply serial interface cards with two ports required that IBM reduce the size of the connector to fit onto a single card back panel. A DE-9 connector also fits onto a card with a second DB-25 connector that was similarly changed from the original Centronics-style connector. Starting around the time of the introduction of the IBM PC-AT, serial ports were commonly built with a 9-pin connector to save cost and space. However, presence of a 9-pin D-subminiature connector is not sufficient to indicate the connection is in fact a serial port, since this connector was also used for video, joysticks, and other purposes.Some miniaturized electronics, particularly graphing calculators and hand-held amateur and two-way radio equipment, have serial ports using a phone connector, usually the smaller 2.5 or 3.5 mm connectors and use the most basic 3-wire interface.Many models of Macintosh favored the related RS-422 standard, mostly using German Mini-DIN connectors, except in the earliest models. The Macintosh included a standard
set of two ports for connection to a printer and a modem, but some PowerBook laptops had only one combined port to save space.The standard specifies 20 different signal connections. Since most devices use only a few signals, smaller connectors can often be used. For example, the 9-pin DE-9
connector was used by most IBM-compatible PCs since the IBM PC AT, and has been standardized as TIA-574. More recently, modular connectors have been used. Most common are 8P8C connectors. Standard EIA/TIA 561 specifies a pin assignment, but the "Yost Serial Device Wiring Standard"[2] invented by Dave Yost (and popularized by the Unix System Administration Handbook) is common on Unix computers and newer devices from Cisco Systems. Many devices don't use either of these standards. 10P10C connectors can be found on some devices as well. Digital Equipment Corporation defined their own DECconnect connection system which was based on the Modified Modular Jack (MMJ) connector. This is a 6-pin modular jack where the key is offset from the center position. As with the Yost standard, DECconnect uses a symmetrical pin layout which enables the direct connection between two DTEs. Another common connector is the DH10 header connector common on motherboards and add-in cards which is usually converted via a cable to the more standard 9-pin DE-9 connector (and frequently mounted on a free slot plate or other part of the housing).

Pinouts
The following table lists commonly used RS-232 signals and pin assignments.
Signal     Origin     DB-25     DE-9
(TIA-574)     MMJ     8P8C ("RJ45")     10P10C ("RJ50")
Name     Abbreviation     DTE     DCE     EIA/TIA-561     Yost (DTE)     Yost (DCE)     Cyclades[4]     Digi (ALTPIN option)[5]     National Instruments[6]    

Cyclades[4]     Digi[7]
Transmitted Data     TxD     ●         2     3     2     6     6     3     3     4     8     4     5
Received Data     RxD         ●     3     2     5     5     3     6     6     5     9     7     6
Data Terminal Ready     DTR     ●         20     4     1     3     7     2     2     8     7     3     9
Data Carrier Detect     DCD         ●     8     1     N/A     2     2     7     7     1     10     8     10
Data Set Ready     DSR         ●     6     6     6     1     8     N/A     5     9     2
Ring Indicator     RI         ●     22     9     N/A     N/A     N/A     N/A     N/A     2     10     1
Request To Send     RTS     ●         4     7     N/A     8     8     1     1     2     4     2     3
Clear To Send     CTS         ●     5     8     N/A     7     1     8     5     7     3     6     8
Common Ground     G     common     7     5     3,4     4     4,5     4,5     4     6     6     5     7
Protective Ground     PG     common     1     N/A     N/A     N/A     N/A     N/A     N/A     3     N/A     1     4

The signals are named from the standpoint of the DTE, for example, an IBM-PC compatible serial port. The ground signal is a common return for the other connections; it appears on two pins in the Yost standard but is the same signal. The DB-25 connector includes a second "protective ground" on pin 1. Connecting this to pin 7 (signal reference ground) is a common practice but not essential.
Note that EIA/TIA 561 combines DSR and RI, and the Yost standard combines DSR and DCD.

Hardware abstraction

Operating systems usually use a symbolic name to refer to the serial ports of a computer. Unix-like operating systems usually label the serial port devices /dev/tty* (TTY is a common trademark-free abbreviation for teletype) where * represents a string identifying the terminal device; the syntax of that string depends on the operating system and the device. On Linux, 8250/16550 UART hardware serial ports are named /dev/ttyS*, USB adapters appear as /dev/ttyUSB* and various types of virtual serial ports do not necessarily have names starting with tty.The Microsoft MS-DOS and Windows environments refer to serial ports as COM ports: COM1, COM2,..etc. Ports numbered greater than COM9 should be referred to using the \\.\COM10 syntax.

Common applications for serial ports

The RS-232 standard is used by many specialized and custom-built devices. This list includes some of the more common devices that are connected to the serial port on a PC. Some of these such as modems and serial mice are falling into disuse while others are readily available.Serial ports are very common on most types of microcontroller, where they can be used to communicate with a PC or other serial devices.

    Dial-up modems
    Configuration and management of networking equipment such as routers, switches, firewalls, load balancers
    GPS receivers (typically NMEA 0183 at 4,800 bit/s)
    Bar code scanners and other point of sale devices
    LED and LCD text displays
    Satellite phones, low-speed satellite modems and other satellite based transceiver devices
    Flat-screen (LCD and Plasma) monitors to control screen functions by external computer, other AV components or remotes
    Test and measuring equipment such as digital multimeters and weighing systems
    Updating Firmware on various consumer devices.
    Some CNC controllers
    Uninterruptible power supply
    Stenography or Stenotype machines.
    Software debuggers that run on a second computer.
    Industrial field buses
    Printers
    Computer terminal, teletype
    Older digital cameras
    Networking (Macintosh AppleTalk using RS-422 at 230.4 kbit/s)
    Serial mouse
    Older GSM mobile phones
    Some Telescopes
    IDE hard drive repair

Since the control signals for a serial port can be easily turned on and off by a switch, some applications used the control lines of a serial port to monitor external devices, without exchanging serial data. A common commercial application of this principle was for some models of uninterruptible power supply which used the control lines to signal "loss of power", "battery low alarm" and other status information. At least some Morse code training software used a code key connected to the serial port, to simulate actual code use. The status bits of the serial port could be sampled very rapidly and at predictable times, making it possible for the software to decipher Morse code.

Settings

Many settings are required for serial connections used for asynchronous start-stop communication, to select speed, number of data bits per character, parity, and number of stop bits per character. In modern serial ports using a UART integrated circuit, all settings are usually software-controlled; hardware from the 1980s and earlier may require setting switches or jumpers on a circuit board. One of the simplifications made in such serial bus standards as Ethernet, FireWire, and USB is that many of those parameters have fixed values so that users can not and need not change the configuration; the speed is either fixed or automatically negotiated. Often if the settings are entered incorrectly the connection will not be dropped; however, any data sent will be received on the other end as nonsense.

Speed
Serial ports use two-level (binary) signaling, so the data rate in bits per second is equal to the symbol rate in bauds. A standard series of rates is based on multiples of the rates for electromechanical teleprinters; some serial ports allow many arbitrary rates to be selected. The port speed and device speed must match. The capability to set a bit rate does not imply that a working connection will result. Not all bit rates are possible with all serial ports. Some special-purpose protocols such as MIDI for musical instrument control, use serial data rates other than the teleprinter series. Some serial port systems can automatically detect the bit rate.

The speed includes bits for framing (stop bits, parity, etc.) and so the effective data rate is lower than the bit transmission rate. For example with 8-N-1 character framing only 80% of the bits are available for data (for every eight bits of data, two more framing bits are sent).Bit rates commonly supported include 75, 110, 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 bit/s.[15] Crystal oscillators with a frequency of 1.843200 MHz are sold specifically for this purpose. This is 16 times the fastest bit rate and the serial port circuit can easily divide this down to lower frequencies as required.

Data bits

The number of data bits in each character can be 5 (for Baudot code), 6 (rarely used), 7 (for true ASCII), 8 (for most kinds of data, as this size matches the size of a byte), or 9 (rarely used). 8 data bits are almost universally used in newer applications. 5 or 7 bits generally only make sense with older equipment such as teleprinters.

Most serial communications designs send the data bits within each byte LSB (Least significant bit) first. This standard is also referred to as "little endian." Also possible, but rarely used, is "big endian" or MSB (Most Significant Bit) first serial communications; this was used, for example, by the IBM 2741 printing terminal. (See Bit numbering for more about bit ordering.) The order of bits is not usually configurable within the serial port interface. To communicate with systems that require a different bit ordering than the local default, local software can re-order the bits within each byte just before sending and just after receiving.

Parity
Main article: Parity bit

Parity is a method of detecting errors in transmission. When parity is used with a serial port, an extra data bit is sent with each data character, arranged so that the number of 1 bits in each character, including the parity bit, is always odd or always even. If a byte is received with the wrong number of 1s, then it must have been corrupted. However, an even number of errors can pass the parity check
Electromechanical teleprinters were arranged to print a special character when received data contained a parity error, to allow detection of messages damaged by line noise. A single parity bit does not allow implementation of error correction on each character, and communication protocols working over serial data links will have higher-level mechanisms to ensure data validity and request retransmission of data that has been incorrectly received.The parity bit in each character can be set to none (N), odd (O), even (E), mark (M), or space (S). None means that no parity bit is sent at all. Mark parity means that the parity bit is always set to the mark signal condition (logical 1) and likewise space parity always sends the parity bit in the space signal condition. Aside from uncommon applications that use the 9th (parity) bit for some form of addressing or special signalling, mark or space parity is uncommon, as it adds no error detection information. Odd parity is more useful than even, since it ensures that at least one state transition occurs in each character, which makes it more reliable. The most common parity setting, however, is "none", with error detection handled by a communication protocol.

Stop bits

Stop bits sent at the end of every character allow the receiving signal hardware to detect the end of a character and to resynchronise with the character stream. Electronic devices usually use one stop bit. If slow electromechanical teleprinters are used, one-and-one half or two stop bits are required.
Conventional notation The D/P/S (Data/Parity/Stop) conventional notation specifies the framing of a serial connection. The most common usage on microcomputers is 8/N/1 (8N1). This specifies 8 data bits, no parity, 1 stop bit. In this notation, the parity bit is not included in the data bits. 7/E/1 (7E1) means that an even parity bit is added to the seven data bits for a total of eight bits between the start and stop bits. If a receiver of a 7/E/1 stream is expecting an 8/N/1 stream, half the possible bytes will be interpreted as having the high bit set.

Flow control
Main article: Flow control (data)

A serial port may use signals in the interface to pause and resume the transmission of data. For example, a slow printer might need to handshake with the serial port to indicate that data should be paused while the mechanism advances a line.Common hardware handshake signals (hardware flow control) use the RS-232 RTS/CTS or DTR/DSR signal circuits. Generally, the RTS and CTS are turned off and on from alternate ends to control data flow, for instance when a buffer is almost full. DTR and DSR are usually on all the time and, per the RS-232 standard and its successors, are used to signal from each end that the other equipment is actually present and powered-up. However, manufacturers have over the years built many devices that implemented non-standard variations on the standard, for example, printers that use DTR as flow control.

Another method of flow control (software flow control) uses special characters such as XON/XOFF to control the flow of data. The XON/XOFF characters are sent by the receiver to the sender to control when the sender will send data, that is, these characters go in the opposite direction to the data being sent. The circuit starts in the "sending allowed" state. When the receiver's buffers approach capacity, the receiver sends the XOFF character to tell the sender to stop sending data. Later, after
the receiver has emptied its buffers, it sends an XON character to tell the sender to resume transmission. These are non-printing characters and are interpreted as handshake signals by printers, terminals, and computer systems.

XON/XOFF flow control is an example of in-band signaling, in which control information is sent over the same channel used for the data. XON/XOFF handshaking presents difficulties as XON and XOFF characters might appear in the data being sent and receivers may interpret them as flow control. Such characters sent as part of the data stream must be encoded in an escape sequence to prevent this, and the receiving and sending software must generate and interpret these escape sequences. On the other hand, since no extra signal circuits are required, XON/XOFF flow control can be done on a 3 wire interface.

"Virtual" serial ports
Main article: COM port redirector

A virtual serial port is an emulation of the standard serial port. This port is created by software which enable extra serial ports in an operating system without additional hardware installation (such as expansion cards, etc.). It is possible to create a large number of virtual serial ports in a PC. The only limitation is the amount of resources, such as operating memory and computing power, needed to emulate many serial ports at the same time.Virtual serial ports emulate all hardware serial port functionality, including Baud rate, Data bits, Parity bits, Stop bits, etc. Additionally they allow controlling the data flow, emulating all signal lines (DTR/DSR/CTS/RTS/DCD/RI) and customizing pinout. Virtual serial ports are common with Bluetooth and are the standard way of receiving data from Bluetooth-equipped GPS modules.Virtual serial port emulation can be useful in case there is a lack of available physical serial ports or they do not meet the current requirements. For instance, virtual serial ports can share data between several applications from one GPS device connected to a serial port. Another option is to communicate with any other serial devices via internet or LAN as if they are locally connected to computer (Serial over LAN/Serial-over-Ethernet technology). Two computers or applications can communicate through an emulated serial port link. Virtual serial port emulators are available for many operating systems including MacOS, Linux, and various mobile and
desktop versions of Microsoft Windows.

浏览 (1667) | 评论 (0) | 评分(0) | 支持(0) | 反对(0) | 产品发布:管理员
将本产品加入收藏
图片
脚注信息
Copyright(C)2009-2010 Reserved by Shenzhen Sinforcon Electronics
Tel: +86-755-85236100    Fax: +86-755-82893356   Email: sales@sinforcon.com Skype: richard90072000   Msn: connectingcables@hotmail.com